Orion-system PT-Link II LON Bedienungsanleitung PDF herunterladen (Seite 26)

PT-Link II LON

Technical Guide

PT-Link II Interface

Use the standard EIA/TIA color code for "CROSS OVER CABLE" as shown.

It is the same as a standard Cat 5 patch cabling. The outer cable jacket should

Be "Orange" in color. This is a straight thru pin 1 to pin 1 cable.

not

RJ-45 Connector as viewed

from the bottom side

RJ-45 Connector as viewed

from the bottom side

Brown/White

White/Brown

Orange/White

White/Blue

Blue/White

White/Orange

Orange/White

White/Green

Blue/White

White/Blue

Green/White

Figure 25: RJ-45 8P8C Cable for WattMaster Cross Over Networking - WattMaster Part #HZ000136

Appendix A & B

External Interface Files (XIF Files)

At start-up the PT-Link II LON creates an external interface ﬁ le (XIF)

called fServer.xif based on the information contained in the PT-Link

II LON’s conﬁ guration ﬁ le (conﬁ g.csv). The PT-Link II LON’s con-

ﬁ guration can be changed by uploading and editing the conﬁ g.csv

ﬁ le; therefore, the XIF ﬁ le must be obtained by uploading it from the

PT-Link II LON.

The recommended procedure for obtaining the XIF ﬁ le for the PT-Link

II LON is to upload it. Remember that this XIF ﬁ le will change when-

ever the conﬁ guration ﬁ le has been changed and downloaded and the

PT-Link II LON restarted. The following are the steps to extract the

external interface ﬁ le (XIF) from the PT-Link II LON:

1.) Start RUINET application.

2.) Select Fieldserver option <1> (this step may be skipped

when application auto-detects PT Link).

3.) From the RUINET Main Menu, type <A> – Data Array

Overview.

4.) You should see 2 array items that are labeled wattmstr-

dump and wattmstr-stats. Ignore these.

5.) You should see 2 additional arrays for the controller

connected.

Example: DA_C162_I0 and DA_C162_I0b.

5.1.) The “b” at the end of the Data Array Name indicates

that it is a mirror array. You can ignore these.

5.2) Verify that your controller is visible or the XIF will not

be generated.

6.) After connection has been veriﬁ ed, you can

now exit to the RUINET Main Menu by pressing <ESC>.

7.) Type <U> – Upload Conﬁ guration.

8.) Type

<O> to select other ﬁ les.

9.) If prompted, press any key to continue.

10.) Type

<R> – Remote Filename.

11.) Type <fserver.xif>.

12. You should now see the name fserver.xif in the column to

the right.

13. Type

<U> to upload the XIF ﬁ le.

14. Once ﬁ nished, you will have an .xif ﬁ le available in the

same directory as the RUINET executable ﬁ le you were

running from.

WARNING: For easier conﬁ guration, set the unit address to 1.

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 59 60

Kommentare zu diesen Handbüchern

Keine Kommentare

Orion-system PT-Link II LON Bedienungsanleitung Seite 26

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Orion-system PT-Link II LON